This post contains affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you. Read our disclosure.
Key takeaways
- Start at about 100 mini lights per foot of tree height, then go to roughly 75 per foot for a soft glow or 150 per foot for a full look.
- Measure height only. Width does not change the rule, though a wide, bushy tree can take the higher number.
- Larger bulbs need far fewer: lighting guides give about 25 to 30 C7 bulbs and 15 to 20 C9 bulbs per foot.
- A pre-lit tree already has lights, so read the bulb count on the box before you add a strand.
- The chart is arithmetic on a rule of thumb. The label on your lights, including how many sets can be joined, always comes first.
In this post12 sections
- How many lights for a Christmas tree: the quick answer
- Step 1: Measure the height, not the width
- Step 2: Pick how bright you want it
- Bulb size changes the number
- Small and tabletop trees: do the math, then check the box
- Pre-lit trees: count before you add
- Power check for a small apartment
- How to put the lights on: trunk to tip
- Myth vs reality: common light mistakes
- Related questions people ask
- Supplies for the lights
- FAQ
Disclosure: some links below are Amazon search links, and we may earn a small commission if you buy. It costs you nothing, and we have not tested these products hands-on.
How many lights for a Christmas tree: the quick answer
Use about 100 mini lights per vertical foot of tree. Go down to about 75 per foot if you want a soft glow, or up to 150 per foot for a full, bright tree. Count the bulbs, not the length of the wire, because the spacing between bulbs changes from set to set.
| Tree height | Soft glow (75 per ft) | Standard (100 per ft) | Full (150 per ft) | 100-light strings at standard |
|---|---|---|---|---|
| 2 ft (tabletop) | 150 | 200 | 300 | 2 |
| 3 ft | 225 | 300 | 450 | 3 |
| 4 ft | 300 | 400 | 600 | 4 |
| 5 ft | 375 | 500 | 750 | 5 |
| 6 ft | 450 | 600 | 900 | 6 |
| 7 ft | 525 | 700 | 1,050 | 7 |
The 100 per foot figure is the common starting point in lighting guides such as 1000Bulbs and Balsam Hill, which also suggest about 50 to 75 per foot for a subtle look and 150 to 200 per foot for a bright one. It is a rule of thumb, and it assumes small mini bulbs.
Hosting a tree-trimming night in a small space? The Hosting Christmas Checklist ($8, 28 pages) has an eight-week countdown, a decor plan for six surfaces and a will-it-fit seating check.
Step 1: Measure the height, not the width
Measure from the floor (or the top of the stand, if it sits on a table) to the tip of the top branch, without the topper. That number in feet is what you multiply. A slim and a full tree of the same height start from the same figure, though a wide, bushy tree has more branches to cover and can take the higher density.
Step 2: Pick how bright you want it
Soft glow (about 75 per foot). Works when the tree is covered in ornaments and you want the lights as a background. It also keeps the cord count down on a small tree.
Standard (about 100 per foot). The safe middle for most trees and the number the chart is built on.
Full (about 150 per foot). For sparse or very tall trees, or when the lights are the main decoration. It takes more strings, so check the outlet section below.
Bulb size changes the number
The rule is for mini lights, which are small and close together. Bigger bulbs sit farther apart, so you need fewer of them. Lighting guides give about 25 to 30 C7 bulbs and 15 to 20 C9 bulbs per foot of tree.
| Bulb type | Bulbs per foot | Look | Fits a small apartment tree? |
|---|---|---|---|
| Mini or fairy | About 100 | Fine, even sparkle | Yes, the usual choice |
| C7 | About 25 to 30 | Larger, retro bulbs | Only on a taller tree |
| C9 | About 15 to 20 | Oversized bulbs | Rarely, they overwhelm a small tree |
Small and tabletop trees: do the math, then check the box
A 2 foot tabletop tree at the standard 100 per foot needs about 200 mini lights, or about 300 for a full look. Many small trees are sold pre-lit, and that count can be lower than the chart, so read the box before you buy more.
For a console or counter, battery fairy lights keep cords off a small surface. Choose a set with a built-in timer so it turns itself off, and keep spare batteries nearby.
Pre-lit trees: count before you add
Look for the bulb count on the box or the listing, and compare it to the chart for your height. If it is below the soft glow number, add one strand. If it is near the standard number, leave it alone and spend the money on ornaments.
Power check for a small apartment
More lights means more strands, and a small apartment often has one outlet near the tree. Every set has a label that says how many sets can be joined end to end, so follow it and never exceed it. Plug the tree into one outlet, not a chain of adapters.
Power check before you plug in
For the best spot for the tree itself, see our guide on where to put a Christmas tree in a small living room. For more light ideas that need no electrician, see renter-friendly lighting ideas. Once the lights are on, our ornament count chart for small, slim and tabletop trees shows how many to hang.
How to put the lights on: trunk to tip
-
Step 1: Test every strand
Plug each set in on the floor and swap out any that flicker or have dark sections before you start.
-
Step 2: Start at the bottom
Put the plug end near the outlet and work up, so you do not run a cord across the room.
-
Step 3: Weave in and out
For each branch, take the strand toward the trunk and back out to the tip. This puts light inside the tree and gives depth.
-
Step 4: Work in sections
Light one vertical section at a time, from the bottom up, and keep the spacing even.
-
Step 5: Check your count
When the bulbs on the tree match your chart number, step back, squint and look for dark patches. Add a little at a time.
-
Step 6: Hide the cord
Tuck the plug end behind the trunk and use a timer so you are not crawling behind the tree to switch it off.
Myth vs reality: common light mistakes
What we like
- Count the bulbs for your tree height
- Use the same white on every strand
- Test strands before wrapping
- Follow the label limit for joined sets
- Use a timer so the tree is off at night
Keep in mind
- Counting by tree width or by feet of wire
- Mixing warm and cool white on one tree
- Joining more sets than the label allows
- Leaving the tree lit when you go out or sleep
- Adding strands to a pre-lit tree without reading its count
Related questions people ask
How many lights for a 6 foot Christmas tree?
About 600 mini lights at the standard 100 per foot, or about 450 for a soft glow and 900 for a full look. That is six 100-light strings at standard.
How many lights for a tabletop Christmas tree?
About 200 for a 2 foot tree and 300 for a 3 foot tree at the standard density. Many small pre-lit trees have fewer, so check the box.
Is it feet of lights or number of bulbs?
Go by the bulb count. The length of a strand depends on how far apart the bulbs are, so two 20 foot sets can have very different counts.
Can I add lights to a pre-lit tree?
Yes, if the label allows it and the colors match. Read the maximum for joined sets first.
Supplies for the lights
Product types mentioned above. We have not tested these hands-on. See our disclosure.
For lighting a small tree
- Start here
LED mini string lights, 100 count, warm white
Typically $8 to $18
The basic unit in the chart: one string per foot of height at standard.
Check price on Amazon for LED mini string lights, 100 count, warm white -
Battery fairy lights with timer
Typically $8 to $20
No outlet needed, handy for a console or tabletop tree.
Check price on Amazon for Battery fairy lights with timer -
Plug-in outlet timer
Typically $8 to $18
Switches the tree off on a schedule so you are not behind it every night.
Check price on Amazon for Plug-in outlet timer -
Slim extension cord, flat plug
Typically $6 to $15
Keeps the plug flush so furniture can sit near the wall.
Check price on Amazon for Slim extension cord, flat plug -
Cord cover for the baseboard
Typically $10 to $20
Hides the run from tree to outlet in a rental, no drilling.
Check price on Amazon for Cord cover for the baseboard
Frequently asked questions
How many lights do you need for a 6 foot Christmas tree?
About 600 mini lights at the standard 100 per foot. Use about 450 for a soft glow or about 900 for a full look.
How many lights for a tabletop Christmas tree?
About 200 mini lights for a 2 foot tree at the standard density, and about 300 for a 3 foot tree. Pre-lit small trees may have fewer, so check the box.
Should I count feet of lights or number of bulbs?
Count the bulbs. Bulb spacing varies, so the length of a strand does not tell you how many lights you have.
How many light strings can you connect together?
It depends on the set. The label states the maximum number of sets that can be joined end to end, and you should never go over it.
Can you add lights to a pre-lit tree?
Yes, if the label allows it. Read the bulb count first, match the white (warm or cool) and add one strand at a time.

Save it for later
Pin this to your Seasonal Decor board so it's there when you need it.
Save to Pinterest





